Roborock Robot vacuum Common Problems
Find your problem in the list below. Each page explains the most likely causes, step-by-step checks you can do yourself, when to call a pro, and the parts that commonly resolve it. 26 problems covered.
Shop Roborock Robot vacuum parts at RepairClinic
- Error 1 — LiDAR turret or laser blocked. The laser distance sensor on top of the robot cannot spin or scan freely, so the robot cannot navigate.
- Error 10 — Filter blocked or not completely dry (worded 'please check that the filter is dry or clean the filter' on E-series and earlier models…
- Error 11 — Strong / high-intensity magnetic field detected (earlier and E-series models). The robot is too close to a magnetic virtual wall / boundary…
- Error 12 — Low battery. The battery level is too low to start or continue cleaning.
- Error 13 — Charging error. The robot is on or near the dock but is not charging properly.
- Error 14 — Battery error. The robot has detected a battery fault, which can also be triggered by the battery being at an abnormal temperature.
- Error 15 — Wall sensor dirty (S7 series and newer; the same fault is Error 26 on Q5+ and older models such as the S5 Max). The side wall sensor cannot…
- Error 16 — Robot tilted. The robot is not level, for example after riding up onto something or being placed on a slope.
- Error 17 — Side brush error. The robot has detected a fault with the side brush drive and the manual's fix is to reset the robot.
- Error 18 — Fan error (called vacuum fan error on S5 Max / S6-era models). The suction fan is reporting a fault and the manual's fix is to reset the…
- Error 2 — Bumper stuck. The front bumper is held in a pressed position, so the robot thinks it is constantly colliding with something.
- Error 21 — Vertical bumper pressed. The vertical bumper / laser rangefinder bumper at the front of the LiDAR area is pressed in and cannot release.
- Error 22 — Dock locator error (Q5+ / S7-era manuals: 'Clean and retry'). On S5 Max-era models the same number is listed differently, as 'wipe the…
- Error 23 — Could not return to dock (Q5+ manual: clean the dock location beacon and retry; S5 Max-era manual words it as clearing the dock charger's…
- Error 24 — Virtual no-go zone or wall detected (S5 Max / S6-era manuals; newer manuals list the same condition without a number). The robot started…
- Error 26 — Wall sensor dirty (Q5+, S5 Max and older models; the same fault is Error 15 on the S7 series and newer). The side wall sensor cannot read…
- Error 27 — VibraRise system jammed (S7 series models with VibraRise mopping only). The vibrating mop module cannot move as it should.
- Error 28 — Robot on carpet (S7 series). The robot was started on carpet when it needed to start on the floor, for example for a mopping run.
- Error 3 — Wheels suspended. One or both wheels have lost contact with the floor, for example after the robot is picked up, rides up onto something…
- Error 4 — Cliff sensor error. The drop sensors on the underside are dirty or are reading a drop, so the robot will not move for safety.
- Error 42 — Dock maintenance brush error (Saros 10, per its manual as summarised from the manual text). If the dock maintenance brush stops at the left…
- Error 5 — Main brush jammed. The main brush cannot turn freely, usually because hair or debris is wrapped around it or its bearings.
- Error 6 — Side brush jammed. The side brush cannot spin freely.
- Error 7 — Wheels jammed. A main wheel cannot turn freely, so the robot cannot drive.
- Error 8 — Robot trapped. The robot is surrounded by obstacles or wedged somewhere and cannot free itself.
- Error 9 — No dustbin. The robot does not detect the dustbin and filter, so it will not start cleaning.