Whirlpool Dishwasher Error Codes
Find your code in the list below. Each page explains what the code means, the most likely causes, step-by-step fixes you can do yourself, and the parts that commonly resolve it. 31 codes covered.
Shop Whirlpool Dishwasher parts at RepairClinic
- F1 E1 — A control-board fault. On older HE models it means a stuck relay on the electronic control board; on newer models Whirlpool's manual…
- F1 E2 — A control-board fault: the board's memory is damaged or corrupted. On some newer manuals the same code is listed as a motor controller…
- F2 E1 — A stuck key: the control detects a button on the user interface stuck or held for over 30 seconds. On models without a display this shows…
- F2 E2 — A communication error between the display / user interface board and the main control board - it is not a leak code.
- F3 E1 — The thermistor / OWI (optical water indicator) sensor signal is open or out of range, so the control cannot read water temperature or soil…
- F3 E2 — The thermistor / OWI sensor signal is shorted, the short-circuit version of the F3 E1 sensor fault.
- F3 E3 — The OWI (optical water indicator) sensor failed to calibrate during the cycle.
- F4 E1 — A wash (circulation) motor error: a communication error between the electronic control board and the wash pump motor.
- F4 E2 — A wash motor error, listed with the same control-to-wash-pump communication fault as F4 E1. On Whirlpool's current support pages F7 E2, not…
- F5 E1 — A door error: the control detects the door is open, or does not see it close within a few seconds of pressing Start on later models.
- F5 E2 — A door error: the control does not detect the door opening between cycles, which it expects to see before a new cycle can start.
- F6 E1 — Platform-dependent: on older HE models this means the dishwasher will not fill / no water is detected; on Whirlpool's current support pages…
- F6 E2 — A water inlet valve electrical error: the inlet valve windings are open or the valve is not responding to the control.
- F6 E3 — Excessive suds / low water level: the wash pump is drawing less power than expected, usually because suds or too little water are in the…
- F6 E4 — The control detected the overfill float switch open - it thinks the dishwasher may be overfilled, often because the float is stuck or the…
- F6 E6 — Incoming water is too cold: the water temperature at fill is below what the control expects (about 120F).
- F6 E7 — A flow meter error: the control is not getting a correct fill signal from the flow meter (not all models have one).
- F6 E8 — A regeneration valve error on models with a built-in water softener: the water softener regeneration valve is not working.
- F7 E1 — Platform-dependent: on older HE models this is a heater fault - the heating element is open or the water does not heat. On newer manuals F7…
- F7 E2 — Platform-dependent: Whirlpool's current support page lists F7 E2 as a wash motor error; on older HE models it means the heating element…
- F8 E1 — Platform-dependent: on older HE models this is a slow drain; on current models 8 flashes, pause, 1 flash is also shown as H2O - no water…
- F8 E2 — Platform-dependent: on older HE models this is a drain pump electrical problem; on current Whirlpool support pages it is a fill valve…
- F8 E4 — Water detected in the drip tray under the tub: the leak / overfill float switch has tripped, the drain sequence begins and the dishwasher…
- F8 E5 — The fill valve is stuck on / stuck open, so water keeps entering and the dishwasher overfills; the drain sequence begins and operation is…
- F9 E1 — Platform-dependent: on current Whirlpool models this is a long drain - the dishwasher is not draining. On older HE models the same code…
- F9 E2 — Platform-dependent: on older HE models the control senses the diverter motor has constant power (a shorted diverter relay); on current…
- FA E1 — A detergent dispenser failure (shown as 10-1 / FA E1 on models that flash the code).
- FA E2 — A vent wax motor electrical problem (shown as 10-2 / FA E2 on flashing-light models); the vent that helps drying is not operating.
- FA E3 — A drying fan / blower motor error: the blower fan speed is less than the control expects (shown as 10-3 / FA E3).
- FA E5 — Water present under the dishwasher (shown as 10 flashes, pause, 5 flashes); the cycle ends. This is the leak-detection companion to F8 E4…
- H2O — Not detecting water: the dishwasher opened its fill valve and did not sense water arriving, so the cycle pauses. Whirlpool also writes this…