Whirlpool Washer Error Codes
Find your code in the list below. Each page explains what the code means, the most likely causes, step-by-step fixes you can do yourself, and the parts that commonly resolve it. 51 codes covered.
Shop Whirlpool Washer parts at RepairClinic
- dET — Detergent cartridge not detected in the dispenser (select models with a bulk detergent cartridge).
- drn — The washer is not draining properly, often an installation problem with the drain hose.
- F0 E1 — A load was detected in the drum during the Clean Washer cycle, which must run empty.
- F0 E2 — Oversuds: the washer detected excessive suds and is running a suds-reduction routine.
- F0 E4 — High temperature error in the wash cycle: the wash water temperature is higher than expected.
- F0 E5 — Off-balance load: the load is unbalanced or too large for the washer to spin safely.
- F02 — Long drain / drain problem on older Duet models: draining takes longer than 8 minutes.
- F05 — Water temperature sensor error on older Duet models: the sensor value is out of range during the heating step.
- F06 — Drive motor tachometer error on older Duet models: the control is unable to detect motor speed.
- F09 — Overflow condition on older Duet models: the overflow contact on the pressure switch stayed closed too long; the door stays locked and the…
- F1 E1 — Main control board failure: a main relay is open or shorted, or the central control has an internal/EEPROM communication error.
- F1 E2 — Motor control error: the motor control unit has an over- or under-voltage fault or has reset repeatedly.
- F2 E1 — Stuck key: a button on the user interface is stuck or has been held down too long.
- F2 E3 — Mismatch error: the main control board and the user interface do not match or cannot communicate as a matched pair.
- F21 — Drain pump / draining fault on Duet-style models: the washer has a water draining issue, the older equivalent of the long-drain codes.
- F3 E1 — Water level pressure sensor error: the pressure sensor signal is missing or out of range.
- F3 E2 — Temperature sensor error: the wash/inlet water temperature sensor (NTC thermistor) is open or shorted.
- F3 E6 — Accelerometer error: the control cannot get a valid signal from the accelerometer that monitors tub movement.
- F34 — Items were detected in the washer during the Clean Washer cycle, the same fault shown as rL on some models.
- F4 E1 — Wash heater relay error: the control cannot detect the expected temperature rise from the wash heater.
- F4 E2 — Heating timeout: the wash water did not heat to the target temperature in the allowed time.
- F5 E1 — Door/lid switch error: on top-load models the lid was up when Start was pushed, and on front-load models the door switch reads open.
- F5 E2 — The door (front-load) or lid (top-load) is not locking properly, so the cycle will not start.
- F5 E3 — Unlock failure: the door or lid lock will not unlock at the end of the cycle.
- F5 E4 — Door not open error: the door was not opened between cycles, so the control does not register a fresh cycle.
- F51 — Motor rotor position sensor (RPS) failure on Cabrio direct-drive models: the control cannot sense the motor rotor position.
- F6 E1 — Communication error: the main control has lost communication with the user interface (HMI).
- F6 E3 — Communication error: the main control has lost communication with the motor control unit.
- F7 E1 — Motor speed sensing error: the motor cannot achieve or report the correct speed for the selected cycle; on belt-drive top-load models this…
- F7 E5 — Shifter fault: the shifter/actuator that changes between agitate and spin is not working correctly.
- F7 E6 — Motor fault: the control detected a problem with the drive motor or its connections.
- F7 E7 — Motor is unable to reach the target RPM during spin.
- F8 E1 — Long fill / low water flow: the washer is taking too long to fill or is sensing too little incoming water. Also shown as LF or Lo FL on…
- F8 E2 — Dispenser system problem: the detergent dispenser did not move or dispense correctly (select models).
- F9 E1 — Long drain: drain time is longer than expected, typically over 8 minutes.
- FH — Water inlet problem: no water is detected entering the machine, or the pressure switch trip was not detected.
- HC — Hot and cold inlet hoses are reversed: the cold hose is on the hot inlet and the hot hose is on the cold inlet. The code appears at the end…
- Int — The cycle was paused or canceled; the washer may take 20 to 30 minutes to stop spinning and drain while this is shown.
- Ld — Long drain on Cabrio models: the water level does not change after the drain pump turns on.
- LdL — The lid is not locking.
- LdU — The lid cannot unlock.
- LF — Long fill: the washer is taking too long to fill with water. This is the top-load display for the same fault as F8 E1.
- lid — The washer lid was left open.
- Lo FL — Low flow: the washer is sensing a low flow of water during fill, the same fault shown as F8 E1 on other models.
- LOC — Control Lock has been activated, so the controls are locked. Also shown as LC on some models.
- Ofb — Out-of-balance load: the washer is running a load-balance correction routine.
- OL — Overload: the washer load was too large, so the washer drains the water and detergent.
- PF — Power failure: the wash cycle was interrupted by a power failure (top-load models).
- rL — Items were detected in the washer during the Clean Washer cycle. Also shown as F34 on some models.
- Sud — Excessive suds: there are too many suds in the washer, so it extends rinsing and may not spin out properly. Also shown as Sd on some models.
- uL — Unbalanced load on Cabrio models: the control detects an off-balance load and runs a mini-cycle to rebalance it.